Arquitetura de Processador MIPS 32-bits
Aqui está uma sugestão de descrição de projeto, otimizada para publicação em uma plataforma como a Freelancer.com, com base no documento que você forneceu. Títu...
Read moreAqui está uma sugestão de descrição de projeto, otimizada para publicação em uma plataforma como a Freelancer.com, com base no documento que você forneceu. Títu...
Read moreI’m looking for a Mandarin-speaking professional in mainland China or Taiwan who already deals with electronic-component distributors. My immediate need is to m...
Read moreI’m building an Automatic Room Light Controller that blends FPGA-level logic with a hands-on Arduino prototype. The goal is simple: when the ambient light is lo...
Read moreI am seeking a highly skilled hardware design engineer for a fixed-term academic project. The objective is to design, implement, and verify a complex 32-bit MIP...
Read moreI need a VHDL IP core that sits between two AXI4-Stream FIFOs, ingests a packet of N values, performs a simple arithmetic tweak, and pushes the result back out....
Read moreRTL Engineer – DMA Subsystem (FPGA / Verilator Simulation) Overview Seeking an experienced RTL engineer to implement and verify a DMA (Direct Memory Access) con...
Read moreI need a Verilog implementation of a CNN accelerator with a DRAM interface. The accelerator should perform matrix multiplication on fixed-size matrices. The DRA...
Read moreI need a concise, synthesizable Verilog finite-state machine that detects the bit sequence 1011 (with overlap) and drives a single-cycle “found” pulse when the...
Read moreI’m looking for a clean Verilog design that realises a 3-bit synchronous counter, counts in ordinary binary from 0 through 7, and drives a single seven-segment...
Read moreI have to count very fast digital pulses—up to 200 MHz—using a Xilinx XC7S50 (Spartan-7, BGA package). The design must implement four independent 64-bit counter...
Read moreШукаємо Embedded-розробника за для переноса програм на PetaLinux ARM64 + оптимізація Розробляємо принтер. Він має клієнт програму на Windows10+, та іншого вже г...
Read moreI need a complete design for a constant-current driver that can source or sink programmable currents through five pairs of output pins, all of which must be abl...
Read moreI’m looking for an experienced embedded developer to build custom firmware for a PCIe DMA device (75t / 100t family). The goal is to emulate full device behavio...
Read moreI have raw captures from both contact (ISO 7816) and contactless (ISO 14443) EMV cards fed directly into an FPGA test rig. My objective is two-fold: complete pr...
Read moreI’m building a motion-control stage that relies on a quadrature rotary encoder operating behind a 100 MHz system clock. I need a compact FPGA module—Verilog or...
Read moreI need a compact DVB packet processor written in Verilog that runs on a Lattice iCE40 FPGA. The sole task is packet filtering—specifically PID filtering—restric...
Read moreWe need an experienced FPGA engineer to implement a PCIe endpoint and custom DMA firmware on an Artix-7 class FPGA carrier. The end result must be a production-...
Read moreI’m looking for an experienced embedded developer to build custom firmware for a PCIe DMA device (75t / 100t family). The goal is to emulate full device behavio...
Read moreI hold a mathematical construct—a quantum-scale, Planck-length vector that iterates through every possible combination of itself. Within this vector reside defi...
Read moreI have a full specification package and SOW ready that outlines a compact electronic card devoted to managing heat inside a consumer-electronics product. The fo...
Read moreWe are looking for an experienced FOGA (Field-Oriented Gate Array) or FPGA programmer to assist with reading data from a high-speed rotary encoder operating at...
Read moreI’m building a simple digital-lock proof-of-concept on a Nexys Artix-7 board using Vivado. At this stage the only feature I need is a basic lock-out mechanism—n...
Read moreI’m looking for an experienced embedded developer to build custom firmware for a PCIe DMA device (35t / 75t family). The goal is to emulate full device behavior...
Read moreI’m starting from a purely conceptual sketch and need a complete design-through-prototype of a programmable pulse generator that sweeps from 1 Hz up to 4.4 GHz....
Read moreWe are looking for a skilled FPGA Design Engineer with solid experience in VHDL development and FPGA toolchains (Vivado, Quartus). You will collaborate remotely...
Read moreI need a RISC-V co-processor that plugs into my existing RISC-V core and dramatically speeds up convolutional layers in a CNN inference pipeline. The sole metri...
Read moreI am seeking an experienced FPGA programmer to develop a custom hardware acceleration solution for high-speed data transfer over Ethernet. Key requirements: - D...
Read moreMy team is tackling a run of mini-projects centred on digital circuit design and we’re looking for an ECE-trained partner who can jump in quickly. The work rang...
Read moreI already have the hardware on my bench— an HMC2003 board, an NVE ALT-0021 board, an OMGS3 ESP32 board and the accompanying analog-to-digital converter. What I...
Read moreI need an experienced FPGA developer to design, program, and test an SDI fiber converter. The converter should support video signal conversion for HD-SDI and 3G...
Read moreI need a compact yet reliable data-acquisition design that runs on an Artix-7 FPGA and lets me capture analog signals up to about 50 MHz from 6 x AD9226 12 bit...
Read moreI need fresh, fully-tested ODOCrypt bitstreams for every model I run—F1, F1+, F1 Ultra and F2—and a clear way to keep them current after each yearly algorithm r...
Read moreSeveral hundred piezoelectric strain gauges will be bonded in a 6 m × 50 mm ribbon-like array. I want to sample the whole field every few milliseconds yet keep...
Read moreMy final-year project revolves around turning the CICIDS 2018 dataset into a real-time Network Intrusion Detection System that flags anomalies in packet-level t...
Read moreI'm finishing my TFG on FPGA implementation, I need someone to help me with the semi-parallel architecture of a filter bank, I have the code done and the design...
Read moreHardware Description – DMA Interposer Card Overview The DMA Interposer Card is a custom PCIe x1 device designed to interface between a host computer and a downs...
Read moreI already rely on Jean-Luc Pons’s open-source VanitySearch (C/CUDA) to grind private keys on GPUs, but I now need the exact same pipeline in hardware. The goal...
Read moreI need a complete, synthesizable SystemVerilog design that turns an off-the-shelf FPGA into a real-time image-processing engine. The pipeline must handle three...
Read moreI’m expanding an FPGA project and need someone who can move comfortably between VHDL development and quick-turn Python scripting. On the FPGA side, the immediat...
Read moreFPGA-Based Image Processing Project Objective: To design and implement a novel FPGA-based image processing system using a combination of hardware description la...
Read more