Composite Building Structural Analysis
I’m finalising the design of a foam-block house that will be coated with a composite polymer-fiber-reinforced Portland cement shell. Before we move into detaili...
Read more
ID / Date
Listing
Link
CFD Topology Optimization: Plate Exchanger
i observed a study on a parallel-plate heat exchanger and now want to convert its findings into a full topology-optimization project. The sole objective is to b...
Read morePost-Mold Deformation Simulation
The project involves running a full post-molding deformation analysis in Moldex3D on a single plastic component so I can refine the part geometry before final t...
Read moreSteel Wire Rope Defect Detection
I need a repeatable, quantitative way to reveal both surface wear / abrasion and hidden problems—internal corrosion, broken wires, any subsurface defect—inside...
Read morenTop Mechanical Porosity Models
I will send you four baseline mechanical composite parts, each built from the same matrix-and-reinforcement system but with different constituent ratios. Your t...
Read moreInduction Motor Design with Ansys
I'm looking for an experienced Ansys Maxwell user to assist in designing an induction motor. The primary goal is to optimize the design for efficiency. Ideal sk...
Read morePlastic Beam Load Analysis
I’m finalising a design that relies on custom-extruded plastic beams and I need a structural engineer to verify that the profiles can safely carry the required...
Read moreUrgent Structural Engineer Needed
I’m looking for a qualified structural engineer who can jump in right away and guide my project from analysis through to stamped drawings and safety-compliant d...
Read moreAutomated DWG-to-IFC Conversion Software
- Title Development of an Automatic DWG to IFC Conversion System (DWG2IFC Converter) Automated transformation of CAD drawings into BIM models with geometry extr...
Read moreCálculo Estructural en Acero
En distintos proyectos de diseño y revision de equipos necesito apoyo puntual en el cálculo de resistencia de materiales para estructuras de acero. El trabajo s...
Read moreBiomechanics FEA Manuscript Drafting
I have completed a finite-element study that simulates the mechanical behaviour of a dental-implant system under static masticatory loading, and I now need a po...
Read moreUAV Wing Design Thesis Package
I’m ready to commission a full MTech-level thesis—complete with a polished PowerPoint deck—on the experimental analysis and optimization of UAV wing design, int...
Read moreStructural Crane Capacity Assessment
I need a seasoned structural engineer to conduct a comprehensive capacity review of our facility’s crane-bearing elements, focusing on the building’s columns an...
Read moreOpenSim Expert Needed (Long-Term) — Gait & Kicking Simulation Support (IK/ID/SO/CMC, Muscle/EMG/Power)
OpenSim Expert Needed (Long-Term) — Gait & Kicking Simulation Support (IK/ID/SO/CMC, Muscle/EMG/Power) Project Type Fixed-price • First task in a long-term coll...
Read moreAbaqus 2D Poroelastic Model Build
I am looking for someone who can open Abaqus/CAE (Standard) and set up a full, working 2-D plane-strain consolidation analysis that couples pore pressure and di...
Read moreSupersonic Aerofoil CFD V&V
I need an ANSYS-based Computational Fluid Dynamics study on supersonic aerofoils, starting with a double-wedge section. The first and most critical milestone is...
Read morePLS-CADD Engineer (LiDAR-Based Power Line Modeling) -- 2
Position Details Position: PLS-CADD Engineer (LiDAR-Based Power Line Modeling) Level: Mid–Senior Domain: Geospatial Engineering / Energy Infrastructure Location...
Read more--- Mechanical Engineers (Only from PAKISTAN) ---
Assalam o alaikum, I am looking for mechanical engineers to be a part of my team and assist me with multiple projects on regular basis. I already have a team of...
Read moreLong-term STAR-CCM+ Expert Needed – Automotive Cabin Windshield Fogging & Demisting CFD Simulation (Multiple Ongoing Projects)
Long-term STAR-CCM+ Expert Needed – Automotive Cabin Windshield Fogging & Demisting CFD Simulation (Multiple Ongoing Projects) Job Description We are looking fo...
Read moreMultiphase CFD Flow Simulation -- 2
I need a detailed CFD study focused on fluid-flow behaviour in a multiphase regime. The primary phase of interest is air; I will share the CAD geometry and oper...
Read moreANSYS FEA Specialist Needed
I need an expert in ANSYS FEA for a project. The analysis required is structural, including static, dynamic, transient, and vibration analyses. Requirements: -...
Read moreErosion Analysis of Sieve mesh in MULTIPHASE Flow using Ansys or COMSOL
Job Title: CFD Engineer Needed for Multiphase Flow Erosion Analysis of Sieve Mesh (Oil & Gas Application) Project Overview: We are conducting a research-based p...
Read moreStatic Analysis for Steel Beam
I need a thorough static load analysis for a steel beam built from 2 sets of two channels welded back-to-back and spaced apartt to behave as an I-beam. Three se...
Read moreDesigning a wishbone based on initial geometry and conditions to ensure certain amount of deformation and stress and buckling.
Please do the lower wishbone part. I need the geometry file and detailed analysis to meet the criterias. The other part does not need to be done. Deadline is ma...
Read moreMechanical FEA for Steel Equipment
I need a Finite Element Analysis (FEA) performed on a mechanical piece of equipment made primarily of steel. The main objective is structural analysis. Ideal Sk...
Read moreHydrogen Iron Melting Simulation Analysis
I need a simulation to study the melting behavior of hydrogen direct reduced iron using confocal microscopy. The project requires analyzing factors such as temp...
Read moreDesign Small Nylon Structural Parts
I am looking for a skilled designer to create small nylon parts intended for structural support. These parts need to function reliably in both indoor and outdoo...
Read moreSolidWorks Stress Analysis Project -- 2
I need assistance with a structural stress analysis project using SolidWorks. The focus is on analyzing a metal structure to evaluate its performance under spec...
Read moreHigh Current PCB Layout Design
I need an experienced PCB designer to create a high-current PCB layout specifically for industrial equipment. The design should be capable of handling currents...
Read moreConcrete Chimney Demolition Analysis
I need a focused vibration analysis report to assess the potential impact on nearby industrial facilities during the demolition of a concrete chimney. Specifica...
Read moreVessel and Tank Designer Needed
I’m looking for an experienced designer to create a tank or vessel specifically intended for oil and gas processing. While the exact type of vessel wasn’t speci...
Read moreEngineered Drawings with State Stamps
I need an engineered drawing for an aluminum platform that supports a generator. The platform has a simple design, and the drawing must include detailed dimensi...
Read morePLS-CADD Engineer (LiDAR-Based Power Line Modeling)
Position Details Position: PLS-CADD Engineer (LiDAR-Based Power Line Modeling) Level: Mid–Senior Domain: Geospatial Engineering / Energy Infrastructure Location...
Read moreInventor Dynamic Simulation Needed
I have a model ready and need someone skilled in Inventor to run a dynamic simulation for it. The key outcome is to determine the force required and generate a...
Read moreMagnetic Field Simulation Using Ansys
I need assistance with simulating the magnetic field density distribution created by a permanent magnet in a Magnetorheological finishing process using Ansys Ma...
Read moreIndustrial Material Handling Machine Design - 08/10/2025 07:35 EDT
I need a full mechanical design for an industrial material-handling machine that will safely transfer heavy loads between workstations on a production floor. I...
Read moreIndustrial Material Handling Machine Design - 08/10/2025 11:10 EDT
I need a full mechanical design for an industrial material-handling machine that will safely transfer heavy loads between workstations on a production floor. I...
Read more5-Axis CNC Postprocessor Design
I need a CAD/CAM specialist who can build a reliable postprocessor for a 5-axis CNC mill, fully compatible with SolidWorks CAM. Scope • Analyse my machine’s kin...
Read morePlaxis Slope Stability Simulation
I need a rapid Plaxis 2D/3D run to check the factor of safety for a recent landslide site in Rishikesh. I will give you: • Google Earth Pro KMZ with coordinates...
Read morePCB FEA: Pogo Pin Stress
I need a finite-element simulation to show how my FR4 board behaves when it is pressed simultaneously from the top and bottom by spring-loaded pogo pins. The bo...
Read more