logism circuit
logism circuits to be completed.
Read more
ID / Date
Listing
Link
Draw a circuit inGerber
This is just the drawing and circuit design
Read moreCIRCUIT USING LOGISIM - COMPUTER SCIENCE
Need someone who is good in circuits (ALU and Register circuits) making using LOGISIM platform.
Read morePCB Board Designing -- 2
PCB Circuit Designing for the connection of sensors, batteries, arduino, gsm and more.
Read moreI need fusion 360 software user who know electric circuit
We need to draw a electric circuit
Read moreBuild me a Circuit on Festo Fluid sim
Must be able to draw a circuit on Festo fluid simm
Read moreAlternate component required for PCB
Alternate part required for PCB Motor Driver DRV8256PRGER
Read morecircuit design resonance and anti resonance
circuit design resonance and anti resonance points and compare with original data
Read more485 Data & 2 Amp fused distributer
I am looking to re-create some small data and power distribution PCB's. We don't have the gerbur files so will need these re done and assistance with a manufact...
Read moreImpedance frequency response from the circuit
find impedance frequency response from the circuit in any spice software
Read moreDesign a Gilbert Mixer using 180nm CMOS technology using CADANCE
See attachment for more information
Read moreUrgent : Looking for DipTrace expert
Hello, I'm looking for an expert in DipTrace schematic and PCB
Read moreInfrared cooking hob motherboard Pcb -- 4
12/24 V DC to 220 V AC portable hob Infrared
Read moreInfrared cooking hob motherboard Pcb -- 2
12/24 V DC to 220 V AC portable hob Infrared
Read moreInfrared cooking hob motherboard
12/24 V DC to 220 V AC portable hob Infrared
Read moreMicrocontroller for alarm clock
Hello, I have an alarm clock project with the following specs: - 8 inch 800 x 600 color display - WiFi to get the time/date from the Internet - 3 alarm settings...
Read moreResearch and find alternative microchip
We're trying to locate an alternative to the MAX31826MUA+T which is a 1-wire device that has a built-in digital temperature sensor and programmable EEPROM. Due...
Read moreRfid reader uart output
I need 125khz rfid reader circuit diagram. It will give me the tag information it read from the 125 khz card from the uart interface.
Read more125 khz RFID reader circuit
Hello I need rfid circuit. The 125 KHZ card needs to work in a way that reads the tag and gives it to me over the uart. In addition, it should also give status...
Read moreDesign a controller
Control project, need to design a controller to fit certain performance measurements from a step input of amplitude 1. Can be P, PI, PID, lead, lag or lead-lag....
Read morePCB design
I need a pcb controller with a battery. Controller will control the intensity of two different color led through two different analog controllers. battery can b...
Read moreReview PCB design in Altium
We have a small PCB design that we’d like reviewed by someone. The files are created in Altium. Essentially the PCB has two LEDs and two photodiodes with amplif...
Read morelooking for an electronic engineer to gotrhough my automated blind project and write a presentation for it
looking for an electronic engineer to gotrhough my automated blind project and write a presentation for it
Read moreEagle CAD Schematic File
I need attached file as Eagle Schematic file for eagle V 6.5 Formfactor is a raspberry board. 65x55mm All Components are smd I need the finished file on: 25.04....
Read moreFM IF Limiting Amplifier Desecrate form.
Need to fine tune / design Limiting amplifier using desecrate transistor. I can provide circuit topology as a reference. first priority is to make attached circ...
Read more3G/LTE communication
I need a compact, low power device that registers a high output (12V) when a phone call is received. Power supply: 12V. The phone call must be received correctl...
Read moreMosfet motor driver.
I would like to use a cheap "brushless speed controller for hobby planes" and have "someone design" a simple "MOSFET power unit" to drive a 3 phase 100v 400A DC...
Read morePCB (printed) /SCB (schematic) designing of a IoT based consumer electronic device
We are looking to the design a smart water bottle that contains sensors to measure the water content. We are looking for a consumer electronic and IoT sensor ex...
Read moreWant to develop constant voltage stabilizer (CVT)
Want to develop constant voltage stabilizer (CVT) *Design*-: (Input):170v to 270v (Output): 230v +/- 1.5% (Cap): 2kva (Type): 1 phase: (50/60Hz) Want complete d...
Read moreExpert Project -- 2
I need someone who has good basic knowledge of semiconductors like knowledge about Jefet mosfet, Rest of the discussion will be later
Read moreHigh voltage circuit Alem
Please check the details of the project. Alem I am waiting.
Read moreesp32 pico hardware design & development services (plan,design to garber files)
reposting this project that is running with freelancer 3 pcb boards, hardware developer & designer that makes for us pcb that will be powered&communicated via u...
Read moredesign a RF Module
406.028MHz ± 1 KHz @5 W (37 ± 2 dB) PERP Bi-Phase L (16K0G1D) 121.5MHz ± 0.005% Amplitude Modulation (3K20A3X) @ 100 mW EIRP (20 dBm) IC：ADF7012 orAFM907N
Read morePCB reverse engineering -- 2
We a pcb we need reverse engineering to be done on it
Read moreVLSI project
This is a VLSI project. It will happen on April 22nd, 2022 from 7h00 pm to 10h00 pm (eastern time). Further details will be provided within this time frame.
Read moreI need an expert on multisim -- 2
I need an expert on multisim
Read moreswitch soldering
need small switch soldered to a circuit board see attached photos
Read moreI need an expert on multisim
I need an expert on multisim
Read morepcb design
need an expert in power electronics
Read moreI need Design for passive filter for 37kW/50HP VFD
I need Design for passive filter for 37kW/50HP VFD to meet the requirements of IEEE 519 of Current Harmonics THD to be less then 5%
Read more