Custom 4-Layer PCB Design for Consumer Electronics
I'm looking for an experienced PCB designer to create a custom 4-layer PCB tailored for a consumer electronics application. This PCB should be compact and desig...
Read moreI'm looking for an experienced PCB designer to create a custom 4-layer PCB tailored for a consumer electronics application. This PCB should be compact and desig...
Read moreI am in need of a firmware over the air feature for my application running on the STM32G0B0VET6, communicated via BLE, specifically through an HC05 module. Key...
Read moreI'm looking for an experienced professional to assemble and test a multi-layer PCB for consumer electronics. The project involves working with various component...
Read moreI'm seeking a seasoned professional to configure and optimize the HMI cMT7280 for my Solar plus genset system. The primary function of this HMI will be to contr...
Read moreI am in need of a firmware over the air feature for my application running on the STM32G0B0VET6, communicated via BLE, specifically through an HC05 module. Key...
Read moreI need an urgent project where my Arduino Uno is connected to the Azure IoT Hub using the SIM800L module. The device needs to send sensor data readings every mi...
Read moreI'm seeking a professional who can assist in designing a 5x5 button keypad for a custom calculator project. The keypad should be compatible with a Raspberry Pi...
Read moreI am seeking a C++ developer with expertise in creating embedded systems, specifically for a communication device. The primary focus of this project is to progr...
Read moreI am building a prototype of a new flight simulation product that requires taking data in from X-Plane datarefs and translating it into commands to one or two o...
Read moreI'm looking for an electronic gadget that serves as a safety indicator by lighting up either green or red upon making contact with the ground. This gadget will...
Read moreI'm working on an IoT project using the A7670C GSM 4G Breakout Board, which is controlled via the Arduino IDE. The board connects perfectly with HTTP, but I'm e...
Read moreI'm looking for a professional in the Sarasota, Florida area to help with a special wiring project. The task involves integrating a 5" BigMack assistive technol...
Read moreI'm looking for a skilled professional who can help me with code development for a Fatek PLC, specifically for a new program aimed at process monitoring. Key Re...
Read moreI'm seeking a professional with extensive experience in STM32 MCU programming, specifically in handling communication protocols such as UART, I2C, SPI, and ETH....
Read moreI'm currently working on a project aimed at controlling death wobbles in high-performance motorcycles. This is achieved by using a steering damper coupled with...
Read moreEstoy buscando un experto que me ayude a cargar en el ESP32 de una PCB el firmware que ya tengo programado. - Tipo de asistencia: Necesito ayuda especialmente p...
Read moreI'm looking for an Arduino expert who can help me with my project. The job involves coding the Arduino to control a relay based on input from PR sensors. Key re...
Read moreI'm looking for a micro transmitter sensor (sonde) compatible with a 512Hz receiver stick. The primary function of this transmitter is to navigate through a 15m...
Read moreWe are seeking an experienced embedded systems developer to build custom firmware for an ESP32. The primary objectives are to implement a Bluetooth Hands-Free P...
Read moreI have to make this assembly on proteus 8 demonstration to test it. I have 4 Lithium accumulators of 4.2 V in series with a resistance of 10ohm. I have a dc vol...
Read moreI have an Arduino-based project utilizing an ESP8266 Access Point protocol. The issue I'm facing is that the code only runs once, necessitating a program restar...
Read moreI'm looking for an expert in embedded software and simulation devices to help set up a system for an NRF9160 Rev2. The primary purpose is to demonstrate the cap...
Read moreI am looking for an experienced embedded systems engineer or wearable device developer to help me build and prototype a smart ring with GPS tracking, emergency...
Read moreUniversal Translation PCB for Coin and Bill Acceptors Project Overview This project aims to develop a universal PCB that acts as a translation module between ve...
Read moreI'm seeking an IoT expert to create a system for remotely monitoring and controlling a water purifier. The project encompasses: - Utilizing an ESP32 or a compar...
Read moreI'm seeking a professional coder with experience in programming for wearable devices. The project involves coding a sweat sensor that measures electrolyte level...
Read moreI'm seeking an expert in IoT and ESP32 boards for a project involving bringing up the board and implementing a communication protocol. The primary use of this p...
Read moreI'm seeking an expert in ICSP programming to help install the built binaries onto PIC18xx target MCUs. The project includes two possible controllers for this pu...
Read moreI'm working with a handheld RGB laser that has 20 modes. It's primarily for personal use, and I need to set it up for ease of use. This project requires someone...
Read moreI'm seeking a professional to explain a Siemens PLC user program to new users. The main focus will be on specific function blocks or instructions within the pro...
Read moreI need an expert in PCB design and microcontroller interfacing to replace the ADS1231 ADC with a CS5532 ADC on my board. The job also requires repositioning the...
Read moreThis is a Bluetooth Audio Player using ESP32. The system includes an Audio Player and Album card using ESP32. The Album card consists of an ESP32, an SD card sl...
Read moreI'm seeking a skilled professional to create a datalogger primarily focused on the Flexray, CAN FD, SPI and I2C communication protocol. This device will be cruc...
Read moreLOCATION: SINGAPORE ONLY need to go on-site for programming, testing and commissioning I'm looking for an expert in Mitsubishi iQ-R Series PLC and GOT2000 Serie...
Read moreI'm seeking a skilled freelancer with profound expertise in embedded systems, industrial automation, and control to assist with a range of tasks. The primary fo...
Read moreI am looking for a professional capable of designing a Bluetooth converter to transform an analog signal. The converter should transmit the sensor signal within...
Read moreI'm looking for an expert in C++ and Arduino who can help me control Delta VFD inverter and other components. I need PLC IDE codes to communicate only.
Read moreI'm seeking a professional developer to create a full-emulated firmware for a DMA. This project has the potential to evolve into a long-term business opportunit...
Read moreI'm looking for an experienced firmware developer with a strong background in microcontrollers, particularly STM32, and expertise in BACnet/IP communications. T...
Read moreI'm looking for a skilled developer to program the DWIN DMG85480C050_03WTR HMI 5-inch display to control and monitor an ultrasonic generator. Key Features: - Ti...
Read more