Rotating Table

$ 250.00 — 750.00 CAD

I am a pub owner from Regina Saskatchewan.
I am building a new pub and came up with an idea for a special table in the pub. The table would hold max 6 people and the table & chairs would all be mounted on a 90" base that I am hoping to get to rotate 1 full orbit each hour.
Attached is a couple of drawings I made up.
I am not good at sketches at all, so I hope I can get the idea across to you through these.
One picture that is labeled “Bottom Base” is a concept of what the bae of the table set would look like underneath.
The idea is that I could build a 90” diameter base that had an outer ring of wheels/casters on it.
These casters would be slightly elevated from the ground attached to a metal ring base, and then a metal ring would sit in top of them, and this metal ring would spin, or move in a round direction on the rollers.
Not unlike a pallet spinner concept, this would just be a bigger version. ( see attached example)

The second drawing is what the table concept would look from a side view. You can see the base, and the rollers on the bottom.
A large pice of wood or metal sits on the rollers, which has the chairs and table mounted to it.
The shaft of the table base is hollow, allowing for us to house the motor inside of it if we can.
This table base sits on a concrete floor which has a basement below it, where the motor could also be mounted, and a rod come up from below attached to the motor.
I would prefer the motor be located in the base/shaft if possible, as I would like to put this concept into other pubs that do not have a basement.

I have no ideas about chains, or additional gears for this.
I was hoping you might have some ideas. I was wanting the table base to do one orbit per hour roughly if possible.

I need someone to help me design how to rotate the table, and let me know what kind of motor I need, with gear reduction.
If I need any additional gears or chain drive.

The motor supplier I have right now needs to know the required torque at the output shaft of the gear unit along with what rpm we want it to rotate.
Unfortunately I do not know this as of yet.
Let me know if you can help me.

Mechanical EngineeringMechanical Design

Similar Freelance jobs:

Cnc Programmer Busellato

CAD/CAMSolidworksMechanical EngineeringLabVIEWAssembly Place Bid

I'm looking for a programmer to program a Busellato Jet 3006 CNC Router - Genesis Software. Please reply ONLY if you are proficient and had knowledge with this machine. Thank you, Al

Full Description of CNC Programmer Busellato

I Need A Mechanical Engineer To Help Develop A Unique Roof Rack For Automobiles

EngineeringCAD/CAMSolidworksMechanical EngineeringProduct Design Place Bid

I am developing a unique roof rack designed to ease loading and unloading.

Full Description of I need a mechanical engineer to help develop…

Mechanical Design Engineer - Hvac System - Solidworks

SolidworksMechanical EngineeringProduct DesignAir ConditioningHeating Systems Place Bid

We have a base design of a hydroponic container farm, we need an expert to design the HVAC system that will fit into this design. We need you to bring in the most cutting edge solutions and calculations to maintain the energy consumption of our product to a minimum. Budget can be negotiated for the right talent.

Full Description of Mechanical Design Engineer - HVAC System - Solidworks

Natural Convection Project

EngineeringMechanical EngineeringPhysicsThermal AnalysisComputational Fluid Dynamics Place Bid

Project involves the study of natural convection within molten liquids

Full Description of Natural convection project

Mechanical Engineer -- 3

CAD/CAMSolidworksMechanical EngineeringManufacturing DesignProduct Design Place Bid

Looking for a Mechanical engineer that can help with an air filter. We can use axial fans to suit our needs (low cost, low wattage, low noise, high efficiency at ~75Pa pressure drop). All the centrifugal fans we have seen have a high pressure drop profile beyond our specs. The direction of flow wise, centrifugal fans would have kept design simpler so it was our first choice (contaminated air enters from the front and pure air leaves from the sides…

Full Description of Mechanical Engineer -- 3

Rve Modeling Of Dual Phase Trip Steel (90% Maartensite And 10% Austenite)

EngineeringSolidworksMechanical EngineeringFinite Element Analysis3D Modelling Place Bid

need for stress strain curve and deformation simulation (ansys and abaqus)

Full Description of RVE modeling of dual phase TRIP steel (90%…

Dialux Design For Flood Light

EngineeringCAD/CAMMechanical EngineeringAutoCAD3D Modelling Place Bid

Dialux report confirming that two nos. of 300 W LED floodlight placed on a 8 mtr. Pole using cantilever of 1 mtr. Length on both sides of the pole are together able to provide minimum 7 lux in the area 25 mtr ( length) X 20 mtr (width) . please send me the price for the same. Thanks & Regards, [Removed by Freelancer.com]

Full Description of Dialux design For Flood light

Simulación Dinámica Ansys

EngineeringMechanical EngineeringFinite Element AnalysisSimulationAnsys Place Bid

Hola soy Henry, necesito a alguien quien pueda realizar una simulación dinámica de proyecto que contiene mecanismo de suspensión por torsión, este mecanismo estaría acoplado a un chasis de un triciclo, el cual serviría como un mecanismo de inclinación (Adjunto fotos de referencia). Los archivos CAD ya los tengo, solo sería la simulación.

Full Description of simulación dinámica ANSYS

Mechanical Engineer Designer

EngineeringCAD/CAMSolidworksMechanical EngineeringProduct Design Place Bid

design of electrical step for vans and minivans

Full Description of mechanical engineer designer

Research Paper

AccountingMechanical EngineeringFinanceElectrical Engineering Place Bid

I need competent writer to help me out with my projects basically academic projects.

Full Description of Research paper

Matlab Problems -- 2

EngineeringMatlab and MathematicaMechanical EngineeringElectrical EngineeringMathematics Place Bid

Can you answer max 4 MATLAB problems that I will send you tomorrow morning (Pakistan local time) 7-9 am?

Full Description of MATLAB Problems -- 2

3d Printing Simulation (dmd Process)

EngineeringCAD/CAMSolidworksMechanical Engineering3D Modelling Place Bid

I want to simulate the Direct metal deposition or Cladding of single metal layer over a substrate using COMSOL/ or/HYPERMESH/ or ABAQUS/or ANSYS /or 3D flow to find the temperature profile and clad dimensions.

Full Description of 3D printing simulation (DMD Process)

Aerospace And Aircraft Dynamics

EngineeringMechanical EngineeringElectrical EngineeringAerospace EngineeringAircraft Systems Place Bid

Hello, I am looking for anyone who is an expert in aerospace and aircraft dynamics. If you fit in this subject , please contact me as I will have a job for you .

Full Description of Aerospace and Aircraft Dynamics

Car Engineer

EngineeringMechanical EngineeringAutomotiveContent Writing Place Bid

Will need someone who knows about car components really well to write me a description.

Full Description of Car engineer

Structural Engineering

Building ArchitectureMechanical EngineeringCivil EngineeringStructural EngineeringAutoCAD Place Bid

Structural Design, Foundations and Calculations.

Full Description of Structural Engineering