Oven Repair

£ 20.00 — 250.00 GBP
I believe the element had been damaged in a fan oven, would need some one to go take a look and repair

Similar Freelance jobs:

Design/prototyping Group Is Needed To Develop A Neuromodulation Audiovisual Wearable Device
A design/prototyping group is needed to develop a neuromodulation audiovisual wearable device. The device has the form-factor of a sleep mask containing LEDs and earbuds to stimulate the brain with light and sound modulated with brainwave frequencies. The device controls the light and sound in accordance with a waveform (stored in an SD card). Required key capabilities include electronic product prototyping, PCP design, embedded SW, signal processing, audio file, low power devices, 32-bit MCU, mechanical closure, wearables and ergonomic devices,…
Full Description of Design/prototyping group is needed to develop a neuromodulation…
Firmware And Hardware Prototype For Streaming Amplifier Using Arm/pwm
I need someone who can build a prototype for a Sitara SoC based streaming audio amplifier project. You must have a spectrum/distortion analyzer. Deliverable: Prototype hardware with firmware/software -Receive streaming Audio stack in ARM -Audio is output thru PRU-ICSS in Sitara via 10 bit PWM / 44 khz -integrated small power amplifier
Full Description of Firmware and Hardware Prototype for Streaming Amplifier using…
Scheme Of Ac/dc Adaptor -- 2
Searching for a specialist who has a little bit of free time and can design a scheme of properly working AC/DC adaptor (output 12VDC=2A) on Altium (included library and Gerber files). As the confirmation, that the adaptor works properly you will be asked a video demonstration, also the results of measurements. If some materials are needed for testing the scheme - we'll cover the cost. Find attached the photo of AC adaptor example.
Full Description of Scheme of AC/DC adaptor -- 2
Barcode Scan Reader - Basquet
I'm looking for an expert in Barcode Scan and electronics, I need a box with barcode readers inside this box to be able to read objects automatically. When I put one object into this box, this object should be identified using a barcode. This box should be able to identify this barcode in any position.
Full Description of Barcode scan reader - basquet
Engine Control Module
Searching for a specialist who has a little bit of free time and can design a scheme of properly working Address engine control unit with integrated LIFEPO4 battery (with protocol management and testing) on Altium (included library and Gerber files). As the confirmation, that the module works properly you will be asked a video demonstration, also the results of testing. If some materials are needed for testing the scheme - we'll cover the cost.
Full Description of Engine Control Module
Pcb Shield For Stm32 Board
need to make a pcb shield for stm32 hz45zi-q board connection following modules 1) max 3865 temperature module ( 2 sets ) 2) Rdl 4-20 ma loop transmitter module ( with power connections ) 3) Eeprom 4) Rtc battery 5) memory card
Full Description of PCB shield for stm32 board
Raspberry Pi Custom Carrier Board
I am looking for someone to design a custom raspberry pi carrier board. The carrier board will have the following: 1. For use with the Raspberry Pi Compute Module 3+ 2. Solid state relay for control 3. 5v Barrel Jack connected for power 4. Wi-Fi Module 5. Ethernet RJ45 Connection 6. HDMI Connection 7. 1xUSB 3.0 Connection 8. Standard 40 pin GPIO Header The form factor of the board is important. Details Below: 1. Ethernet RJ45, Barrel Jack Connector and…
Full Description of Raspberry Pi Custom Carrier Board
Pic18f4550 Design Project
This is a project on PIC18F4550 using MIKRO C and physical components as well as Proteus (not 100% essential) From reading the text, designing the code and building it in physical. It´s an exam so it´s time measured and starts in 22 hours. (Thursday 24 at 07:00 am Mexico time) It lasts 3 hours I attach SAMPLE proyects and solutions, the project is really similar.
Full Description of PIC18F4550 DESIGN PROJECT
© 2006 — 2024 hirelancer.com is an affiliate website, listing the freelance projects. We are collaborating with other sites like getFreelancer.com. Feel free to bid on any project and good luck! You will need register first, before bidding or posting projects. Basic memberhsip is always free. We might earn commissions from referring you. You will never ever pay additional fees for we referred you.