Barcode Scan Reader - Basquet

€ 250.00 — 750.00 EUR
I'm looking for an expert in Barcode Scan and electronics,
I need a box with barcode readers inside this box to be able to read objects automatically.
When I put one object into this box, this object should be identified using a barcode.
This box should be able to identify this barcode in any position.

Similar Freelance jobs:

Build An Sram Memory Compiler Based On "openram" Project.
A configurable SRAM compiler written in Python to tile the bit cells and address decoder blocks, extract the Verilog and parasitic RC models, and generate the GDS2 block database. The project should leverage the "openRAM" open source code as much as possible to achieve the above objectives.
Full Description of Build an SRAM memory compiler based on "openRAM"…
Design/prototyping Group Is Needed To Develop A Neuromodulation Audiovisual Wearable Device
A design/prototyping group is needed to develop a neuromodulation audiovisual wearable device. The device has the form-factor of a sleep mask containing LEDs and earbuds to stimulate the brain with light and sound modulated with brainwave frequencies. The device controls the light and sound in accordance with a waveform (stored in an SD card). Required key capabilities include electronic product prototyping, PCP design, embedded SW, signal processing, audio file, low power devices, 32-bit MCU, mechanical closure, wearables and ergonomic devices,…
Full Description of Design/prototyping group is needed to develop a neuromodulation…
Firmware And Hardware Prototype For Streaming Amplifier Using Arm/pwm
I need someone who can build a prototype for a Sitara SoC based streaming audio amplifier project. You must have a spectrum/distortion analyzer. Deliverable: Prototype hardware with firmware/software -Receive streaming Audio stack in ARM -Audio is output thru PRU-ICSS in Sitara via 10 bit PWM / 44 khz -integrated small power amplifier
Full Description of Firmware and Hardware Prototype for Streaming Amplifier using…
Scheme Of Ac/dc Adaptor -- 2
Searching for a specialist who has a little bit of free time and can design a scheme of properly working AC/DC adaptor (output 12VDC=2A) on Altium (included library and Gerber files). As the confirmation, that the adaptor works properly you will be asked a video demonstration, also the results of measurements. If some materials are needed for testing the scheme - we'll cover the cost. Find attached the photo of AC adaptor example.
Full Description of Scheme of AC/DC adaptor -- 2
Engine Control Module
Searching for a specialist who has a little bit of free time and can design a scheme of properly working Address engine control unit with integrated LIFEPO4 battery (with protocol management and testing) on Altium (included library and Gerber files). As the confirmation, that the module works properly you will be asked a video demonstration, also the results of testing. If some materials are needed for testing the scheme - we'll cover the cost.
Full Description of Engine Control Module
I Need Software Engineering Tutor
Give me a price for one session Topics 1- Introduction to Software engineering 2- Software process 3- Feasibility analysis 4- Software requirements 5- Applying use cases 6- System models 7- Architectural Design 8- Software testing
Full Description of I need software engineering tutor
Pcb Shield For Stm32 Board
need to make a pcb shield for stm32 hz45zi-q board connection following modules 1) max 3865 temperature module ( 2 sets ) 2) Rdl 4-20 ma loop transmitter module ( with power connections ) 3) Eeprom 4) Rtc battery 5) memory card
Full Description of PCB shield for stm32 board
© 2006 — 2024 hirelancer.com is an affiliate website, listing the freelance projects. We are collaborating with other sites like getFreelancer.com. Feel free to bid on any project and good luck! You will need register first, before bidding or posting projects. Basic memberhsip is always free. We might earn commissions from referring you. You will never ever pay additional fees for we referred you.