Web|Software|Desktop|Mobile developers. Find a remote job.

Realization of a demonstrator on ST STM32F769I-DISCO board (4'' 480x800). STM32Cube - FreeRTOS – TouchGFX The application is defined (screens, sequences to screen or function). Reading one sensors on usart and other messages on canbus (defined messages). Show informations on GUI. Sending messages on canbus (defined messages). Save user's parameters in flash. Source full project Stm32Cube/gfx to deliver. Option: add bootloader IAP on USB to allow the program update (there are 2 flash banks of 1MB. Application is less than…

I have Arvento imt14 branded vehicle tracking devices about 200 pcs. I want to custom firmware to the devices. The firmware must send various gps data and vehicle ignition status to my own server over TCP/IP. The devices original firmware send GPS data to Arvento's server so I dont use their server anymore. The devices has STM32F103VET6 , Telit GE865 GSM modem and Ublox Neo6M GPS module Also every device must have a id number in firmware. We have no…

We are a project team collaborating with Aqua AG, a company specializing in irrigation systems based in Switzerland. We are contacting you to request a collaboration regarding the development of an IoT-based irrigation system with the eventual goal of mass production and commercial use. Our team has already developed a prototype version, which consists of a fully functional irrigation controller with the ability of remote connectivity (control and monitoring via a web app we developed). This controller can be programmed…

We are a project team collaborating with a company, specialising in irrigation systems, based in Switzerland. We are contacting you to request a collaboration regarding the development of an IoT-based irrigation system with the eventual goal of mass production and commercial use. Our team has already developed a prototype version, which consists of a fully functional irrigation controller with the ability of remote connectivity (control and monitoring via a web app we developed). This controller can be programmed to control…

Hi all, I need help with firmware development for a GPS tracker prototype I'm building. It will be based on the STM32 microcontroller and will use the SIM868 as the communications module for GPS/GPRS/BLUETOOTH. Requirements: - Set up communication between STM32 and SIM868 over UART using AT commands - Sending GPS data to remote server over TCP/IP using a defined communication protocol (GT06/TK06 or other, open for suggestions) - Reading and configuring of device parameters using SMS - Reading accelerometer…

stm32f103c6t8 foc brushless motor controller

stm32f103 foc brusless motor controller2

We need a small project that implements only a simple communication between two STM32F303 boards with nRF24 wifi. we would like to send struct from one board to another and another struct back. The struct should be something like: typedef struct { uint32_t DataFlag; uint16_t dataA; uint16_t dataB; }DataPack; the project should be built with STM32CubeIDE and C++

I need a port of LVGL to custom board with STM32F429BIT6 + SDRAM + LCD(RGB888 + GT911) using HAL(cubeMX) and Keil MDK-ARM.

The project involves using an STM32F446-Nucleo and X-Nucleo-CCA02M2 to capture sound using the PMD microphones and output sound via I2S to a MAX98357 amp. I need some familiar with the STM32F4 series and using STM32CubeIDE to build firmware.

I need to program a "pulse train" based on a cortex-m4 MCU BOARD. USING STM32CubeIde The pulse train is generated through timer and timer interrupt. The train pulse is variable in frequency There must be a up ramp in frequency and down ramp frequency routine I'm electronic engineer from Chile, have a bit of experience on progamming, BUT dont have time to get into all registers details on this MCU architecure and STM32CubeIde programming enviroment. I can of course, try…

I have a trainee. We have an electronics project. We have some a functional electronics board with code. The code however was left by someone in a hurry without explaining the code in detail. So we need someone who can check the code and understand it. The trainee needs help with -understanding the structure of the code, - teach how to structure the code, -How to debug and improve the functionality of the device. Work is 10 hours per week.

Data logging Sensors: {Accelerometer, Gyroscope, Temperature, GSR} To SD Card

Hello, I am developing a new USBC headset. I have a few problems. What I wanted was to simultaneously implement the functionality of serial data communication and audio/MIC between all phones and headset boards. An STM32L432 MCU is used for the serial data interface and an audio codec IC is used for the audio streaming data interface. STM32 MCU and audio codec IC connected to USBC connector via USB HUB. I designed the hardware with STM32 and wrote the firmware…

I want to use the can port as serial communication. Between 100-800kbaud rates, canbus and serial same pin stm32f103 pb8-9 serial communication liblary make. I want to use canbus port as serial port don't write without understanding don't waste time