Rapid Prototyping

I need some one to enter some data for me. The documents are provided separately. The final format of the entered data should be consistent and standardised. Please message me if you have any questions.

do the work

Looking for talented 3D model artists and VFX specialists to work with for the long term. Need 5 or more models a week. If you have any of the following skills, please submit a proposal. Thank you! -Experienced in 3D modelling -Experienced in 3D rigging & animation -Experienced in VFX -Use Unreal Engine -Use Blender -Good with character models -Good with environment designs -Good with both cartoon and anime styles -Quick delivery and fast communication -Hiring 10 or more workers

A design/prototyping group is needed to develop a neuromodulation audiovisual wearable device. The device has the form-factor of a sleep mask containing LEDs and earbuds to stimulate the brain with light and sound modulated with brainwave frequencies. The device controls the light and sound in accordance with a waveform (stored in an SD card). Required key capabilities include electronic product prototyping, PCP design, embedded SW, signal processing, audio file, low power devices, 32-bit MCU, mechanical closure, wearables and ergonomic devices,…

I need someone who can build a prototype for a Sitara SoC based streaming audio amplifier project. You must have a spectrum/distortion analyzer. Deliverable: Prototype hardware with firmware/software -Receive streaming Audio stack in ARM -Audio is output thru PRU-ICSS in Sitara via 10 bit PWM / 44 khz -integrated small power amplifier

Dear Developer. I have a unity project and I need someone who has a good pc to bake the light and fix the fps. I tried to do the following : 1- I baked the light and I saw the black area 2- I did the LOD for most of the 3D models and it is the same 3- I have a good PC to run the build and the fps is only 30 hardly reaching the 50 and I…

- Zeichnen von Kabelbäumen - Kabelverlegung und Anbindung - Konstruktion von Kabelbahnen - Bauraumabsicherung von Bordnetzen - Siemens NX Routing (Wire) - Grundsatzwissen zu technischen Normen und EMV - 2D-Ableitung von den 3D-Modellen für die Formaboards in der Produktion - Stecker und Pin-Belegung, sowie Steckerplatten

Searching for a specialist who has a little bit of free time and can design a scheme of properly working AC/DC adaptor (output 12VDC=2A) on Altium (included library and Gerber files). As the confirmation, that the adaptor works properly you will be asked a video demonstration, also the results of measurements. If some materials are needed for testing the scheme - we'll cover the cost. Find attached the photo of AC adaptor example.

Arduino Bluetooth Controlled Car

I'm looking for an expert in Barcode Scan and electronics, I need a box with barcode readers inside this box to be able to read objects automatically. When I put one object into this box, this object should be identified using a barcode. This box should be able to identify this barcode in any position.

need for stress strain curve and deformation simulation (ansys and abaqus)

Searching for a specialist who has a little bit of free time and can design a scheme of properly working Address engine control unit with integrated LIFEPO4 battery (with protocol management and testing) on Altium (included library and Gerber files). As the confirmation, that the module works properly you will be asked a video demonstration, also the results of testing. If some materials are needed for testing the scheme - we'll cover the cost.

We have a set of plans (43 plans) and we want the design that we have in 2D pdf to be made in CATIA 3D. Assigning to each piece a catpart and to the sets its corresponding catproduct. There are some commercial or hardware elements with the reference in the plans and their corresponding brand. These elements must also be in the 3D design. Attached you can find the assembly drawing of the total design. The pieces will have a…

Arduino Voice Controlled Car At Home

Arduino Obstacle Avoiding Car At Home