4 Simple PCB designed using EasyEDA.
Budget: $10 – $120 AUD
I'm after an IMMEDIATE TURN AROUND on this, if you can't do it within 48hrs don't bid.
All components must be in stock at JLCPCB if not that must be in stock LCSC.
Board 1
Simple WS2812 Board
Circle, 80mm, 2 holes in center, with roughly 20 WS2812 around the outside.
2 x 2 lots of wire holes. eg. input/output, +, -
Board 2
4 x WS2812
30x30mm
JST Connector.
Board 3
Input Output board for daisy chaining WS2812
- Input signal connector
- Power connector
Then has 10 JST connectors which are, input, output, +, -
Board should have a small LED for seeing if it has 'power'.
Board should also have some small capacitors on it as needed for power draw of WS2812.
Board 4 (this design is done, needs minor modification).
Very basic, mini Power Distribution board.
1 input connector 3 output connectors and 2 fuses.
Needs to simply have 'leds' for 5v power and 12v power after the fuse, so you can tell it is working and has power.
Board 5 and 6
The one that will take the most time is a ESP32 Breakout board.
Utilizing a ESP32 Wroom ESP-WROOM-32 WIFI Bluetooth Development Board.
A main board for the dev board to be soldered to, which will.
- Have an RJ45 connector going to sub board.
- Have output connector for WS2812.
- Have power LED so can tell the board is booted and has power.
A Sub Board
- Has RJ45 Connector.
- Has 6 Optoisolated inputs, which can then be used as triggers (program on main board through code).
- Has a power indicator LED.
Bid one or all, i may split the project across two freelancers to get it done on time.
If doing board 5/6 there will be a possible PART B for coding.
All components must be in stock at JLCPCB if not that must be in stock LCSC.
Board 1
Simple WS2812 Board
Circle, 80mm, 2 holes in center, with roughly 20 WS2812 around the outside.
2 x 2 lots of wire holes. eg. input/output, +, -
Board 2
4 x WS2812
30x30mm
JST Connector.
Board 3
Input Output board for daisy chaining WS2812
- Input signal connector
- Power connector
Then has 10 JST connectors which are, input, output, +, -
Board should have a small LED for seeing if it has 'power'.
Board should also have some small capacitors on it as needed for power draw of WS2812.
Board 4 (this design is done, needs minor modification).
Very basic, mini Power Distribution board.
1 input connector 3 output connectors and 2 fuses.
Needs to simply have 'leds' for 5v power and 12v power after the fuse, so you can tell it is working and has power.
Board 5 and 6
The one that will take the most time is a ESP32 Breakout board.
Utilizing a ESP32 Wroom ESP-WROOM-32 WIFI Bluetooth Development Board.
A main board for the dev board to be soldered to, which will.
- Have an RJ45 connector going to sub board.
- Have output connector for WS2812.
- Have power LED so can tell the board is booted and has power.
A Sub Board
- Has RJ45 Connector.
- Has 6 Optoisolated inputs, which can then be used as triggers (program on main board through code).
- Has a power indicator LED.
Bid one or all, i may split the project across two freelancers to get it done on time.
If doing board 5/6 there will be a possible PART B for coding.